Helonic

Stair pressurization on life safety and mechanical sheets

Helonic is an AI construction drawing analysis platform for people check stair pressurization during plan review. The fan, the outdoor intake, the relief, and the stair doors have to show up together on the life safety, mechanical, and electrical sheets

A pressurized stair passes review when the life safety plan, the mechanical plan, the roof plan, and the electrical sheets all show the same system: a supply fan, an outdoor air intake away from smoke sources, a way to keep the pressure in range, and stair doors that still open with the force the code allows. Helonic matches each pressurized stair to its fan, relief, and power. IBC Section 909.20 sets the pressure range. The common failure is a stair labeled pressurized on one sheet and drawn as an ordinary stair on another.

When does a stair need pressurization?

In a high-rise, IBC Section 403.5.4 requires every required interior exit stair serving floors more than 75 feet above the lowest level of fire department vehicle access to be a smokeproof enclosure. Underground buildings have a similar rule.

A smokeproof enclosure normally has a vestibule. IBC Section 909.20 lets a fully sprinklered building skip the vestibule if the stair is pressurized instead. The stair has to hold at least 0.10 inch of water (25 Pa) and no more than 0.35 inch of water (87 Pa) relative to the building, with all stair doors closed, under the worst stack and wind conditions expected.

The upper limit protects the doors. IBC Section 1010.1.3 limits the force to set a side-swinging egress door in motion to 30 pounds. Too much pressure and people on the floor can't open the stair door. If the stair uses a vestibule instead, see smokeproof stair vestibule size and door swing.

Which sheet shows each part of the system?

Stair pressurization crosses more disciplines than almost any other life safety system. Each row is a place where the sheets can drift apart.

ItemSheetWhat to check
Supply fanMechanical plan, roof plan, equipment scheduleThe same fan tag and location appear on all three, and the fan serves the stair the life safety plan names.
Outdoor intakeRoof planThe intake sits away from exhaust outlets, generator exhaust, and smoke exhaust discharge.
Supply pointsMechanical plans and sectionsTall stairs usually need supply at several levels so pressure stays even from top to bottom.
Pressure controlMechanical plan and sequenceA relief damper, a variable speed drive, or another control keeps the stair below 0.35 inch.
Stair doorsDoor schedule and hardware setsThe undercut, gaskets, and closers match the leakage the pressurization design assumed.
Start and powerFire alarm matrix and electrical one-lineThe fire alarm starts the fan, and the fan and its controls are on standby power.

Where do the sheets usually disagree?

  • The life safety plan labels a stair as pressurized, and the mechanical plan has no fan for it.
  • The fan intake on the roof plan sits next to a kitchen exhaust or a generator exhaust.
  • There is no relief path, so the fan sized for doors-open conditions overpressurizes the stair when the doors are closed.
  • The door schedule calls for a large undercut on the stair doors, while the pressurization design assumed tight, gasketed doors.
  • The fan is on normal power only on the electrical one-line.
  • The fire alarm matrix never starts the fan. The fire alarm sequence of operations guide covers how to read that matrix.

How do you check a pressurized stair in one pass?

  1. List every stair the life safety plan calls smokeproof or pressurized.
  2. Match each stair to a fan tag on the mechanical plan and the equipment schedule.
  3. Check the intake on the roof plan for nearby exhausts.
  4. Look for a relief damper, a variable speed drive, or another way to hold the pressure range.
  5. Read the stair door hardware and undercut against the design assumptions.
  6. Check the fire alarm matrix and the electrical one-line for the start signal and standby power.

Smoke control systems also get special inspection and testing under IBC Section 1705, so a mismatch caught in plan review is far cheaper than one caught at the pressure test. The broader habit is described in how to review construction drawings.

Drawing Review Checkpoint

Ask for the pressurization calculation or design narrative. If it assumes small door gaps and the door schedule says something else, the pressure test at the end of the job is the first time anyone finds out.

How does Helonic check stair pressurization?

Helonic matches each pressurized stair on the life safety plan to a fan on the mechanical and roof plans, a start signal on the fire alarm matrix, and standby power on the electrical sheets. It flags a stair with no fan, a fan with no relief, or an intake drawn beside an exhaust. The fire and life safety checks cite the sheet for each finding.

Findings are decision support. The mechanical engineer of record decides what changes. For how this review fits a project, see AI for construction drawings.

Practitioner insight

“The fan shows up on the roof plan, but nobody checks the door schedule. The calc assumed tight doors, the doors arrive with a big undercut, and the stair never reaches 0.10 inch at the test.”

Common finding in high-rise life safety and mechanical coordination review.

Stair Pressurization FAQs

What pressure does a pressurized stair need?
IBC Section 909.20 requires at least 0.10 inch of water (25 Pa) and no more than 0.35 inch of water (87 Pa) in the stair relative to the building, with all stair doors closed, under the worst expected stack and wind conditions.
Does a pressurized stair need a vestibule?
Not in a fully sprinklered building that uses the pressurization alternative in IBC Section 909.20. Without pressurization, a smokeproof enclosure is reached through a vestibule or an open exterior balcony.
Why is there a maximum stair pressure?
Too much pressure makes the stair doors hard to open. IBC Section 1010.1.3 limits the force to set a side-swinging egress door in motion to 30 pounds, and the 0.35 inch cap keeps the doors usable.
Does the stair pressurization fan need standby power?
Yes. IBC Section 909.20 requires standby power for the stair shaft ventilation system and its detection. The electrical one-line should show the fan on the standby source.
Who tests a pressurized stair?
Smoke control systems get special inspection and testing under IBC Section 1705. The special inspector measures the pressure difference and the door opening force before the building is occupied.
MG

Manas Gandhi

Co-founder & CTO, Helonic

Manas is the co-founder and CTO of Helonic, where he leads engineering and AI research for construction drawing analysis. He works directly with structural, MEP, civil, and fire protection engineers to translate the way they review drawings into AI systems that flag the issues that actually matter in the field. Before Helonic, he built machine learning pipelines for technical document understanding and has spent the last several years interviewing licensed design engineers and discipline leads to ground product decisions in real practice rather than industry assumptions.

Areas of focus
  • AI for technical document understanding
  • Cross-discipline coordination workflows
  • Code compliance automation (IBC, NEC, NFPA, IPC, IMC, ASCE)
  • Structural and MEP drawing review systems

How this page was researched: Requirements were checked against IBC 2021 Sections 403.5.4, 909.20, and 1010.1.3, and the IBC Section 1705 special inspection requirements for smoke control systems.

Last reviewed by Manas Gandhi · October 6, 2026

Catch stair pressurization gaps before issue

Helonic matches every pressurized stair to a fan, a relief path, a start signal, and standby power.