Helonic

Exit passageway requirements on drawings

Helonic is an AI construction drawing analysis platform for people check exit passageways during plan review. The passage has to stay a rated enclosure and can't pick up ordinary tenant doors along the way

An exit passageway passes review when it stays a rated enclosure from end to end, its only openings and penetrations are the ones IBC Section 1024 allows, and nothing along the way cuts the required width. Helonic flags anything that breaks the enclosure. The passage carries at least the rating of the stair it extends, often 2 hours. Most misses happen when a tenant plan or a later revision adds an ordinary door, a duct, or a closet that opens into the passage.

What is an exit passageway?

An exit passageway is an exit that runs horizontally. It most often carries an interior exit stair from where it lands to the outside or to a public way. IBC Section 1024 covers it.

The passage is built with fire barriers, horizontal assemblies, or both, rated at least 1 hour and not less than the rating of any interior exit stair it connects to. Its width is at least 44 inches, or 36 inches where it serves fewer than 50 occupants, and never less than the capacity the occupant load requires. It ends at an exit discharge or a public way.

Where the passage extends a stair, Section 1023.3.1 puts a rated fire door between the stair and the passage. The egress basics page explains how exits, exit access, and exit discharge fit together.

What can open into an exit passageway?

Section 1024.5 limits openings to those needed for exit access from normally occupied spaces and for leaving the passage. Elevators can't open into it. A storage room, an electrical room, or a janitor closet is not a normally occupied space, so a door from one of them into the passage is a problem. Every opening that is allowed gets a rated, self-closing door.

Section 1024.6 limits penetrations to a short list:

  • Equipment and ductwork for independent pressurization of the passage.
  • Sprinkler piping.
  • Standpipes.
  • Electrical raceway for fire department communication.
  • Electrical raceway that serves the passage itself.

A duct main, a domestic water line, or a conduit run that serves the tenant next door can't cross the passage. Listed firestop systems at the allowed penetrations are covered in the firestopping guide.

Which sheet shows each part of the passage?

ItemSheetWhat to check
EnclosureArchitectural plans and wall-type legendThe rating matches the stair it extends, and the walls run to the deck or to a rated lid.
DoorsArchitectural plans and door scheduleOnly doors from normally occupied spaces, each rated and self-closing.
WidthEnlarged planAt least 44 inches clear, and door swings stay within the encroachment limits.
PenetrationsMechanical, plumbing, and electrical plansOnly the items Section 1024.6 allows cross the enclosure.
TerminationGround floor and site plansThe passage ends at an exterior exit discharge or a public way.
Tenant workTenant improvement drawingsLater tenant sets do not add doors or penetrations the base building never had.

Where do the sheets usually disagree?

  • A retail tenant set adds an unrated back door from a stockroom into the passage, where the base building showed a blank rated wall.
  • An electrical room or trash room door opens into the passage.
  • A duct main serving the adjacent tenant crosses the passage ceiling on the mechanical plan.
  • The passage walls carry a 1-hour tag while the stair it extends is 2-hour.
  • A standpipe hose valve or a semi-recessed cabinet projects into the required width.
  • The passage ends in a lobby rather than outside.

Tenant work is the biggest source of drift. The tenant improvement as-built risk page covers why the base building drawings stop matching the space.

How do you check an exit passageway in one pass?

  1. Find the passage on the life safety plan and note the stair it extends.
  2. Read every wall tag along the passage and compare the rating to the stair.
  3. List every door that opens into the passage and what room it serves.
  4. Overlay the mechanical, plumbing, and electrical plans and list every crossing.
  5. Measure the clear width at its narrowest point with doors drawn open.
  6. Confirm the passage ends outside or at a public way.

Reading one exit through every discipline is the core of how to review construction drawings.

Drawing Review Checkpoint

Check the tenant improvement drawings against the base building. The shell set usually gets the passage right, and the first tenant revision is where a door shows up.

How does Helonic check exit passageways?

Helonic reads the passage across the architectural, mechanical, plumbing, and electrical sheets. It flags a wall rated below the stair, a door from a storage or service room, and a duct or pipe that does not belong in the enclosure. The egress compliance checks cite the sheet and the grid for each finding.

Findings are decision support. The architect decides what changes. For how this review fits a project, see AI for construction drawings.

Practitioner insight

“The base building passage is clean. Then the tenant set adds a stockroom door and a duct to a rooftop unit, and nobody pulls the shell drawings to compare.”

Common finding in retail and mixed-use egress review.

Exit Passageway FAQs

What is an exit passageway?
An exit passageway is a rated, enclosed exit that runs horizontally. It usually carries an interior exit stair from where it lands to the outside or to a public way. IBC Section 1024 covers it.
What fire rating does an exit passageway need?
At least 1 hour, and not less than the rating of any interior exit stair it connects to. A passage that extends a 2-hour stair needs 2-hour walls.
Can a tenant door open into an exit passageway?
Only a door from a normally occupied space that needs the passage for exit access, and only as a rated, self-closing door. Storage rooms, electrical rooms, and closets can't open into the passage, and elevators can't open into it either.
What can penetrate an exit passageway?
IBC Section 1024.6 allows ductwork for independent pressurization, sprinkler piping, standpipes, raceway for fire department communication, and raceway that serves the passage itself. Other ducts and pipes can't cross it.
How wide does an exit passageway have to be?
At least 44 inches, or 36 inches where it serves fewer than 50 occupants. It also has to be wide enough for the capacity the occupant load requires.
MG

Manas Gandhi

Co-founder & CTO, Helonic

Manas is the co-founder and CTO of Helonic, where he leads engineering and AI research for construction drawing analysis. He works directly with structural, MEP, civil, and fire protection engineers to translate the way they review drawings into AI systems that flag the issues that actually matter in the field. Before Helonic, he built machine learning pipelines for technical document understanding and has spent the last several years interviewing licensed design engineers and discipline leads to ground product decisions in real practice rather than industry assumptions.

Areas of focus
  • AI for technical document understanding
  • Cross-discipline coordination workflows
  • Code compliance automation (IBC, NEC, NFPA, IPC, IMC, ASCE)
  • Structural and MEP drawing review systems

How this page was researched: Requirements were checked against IBC 2021 Section 1024 for exit passageway width, construction, openings, and penetrations, and Section 1023.3.1 for stair extensions.

Last reviewed by Manas Gandhi · October 8, 2026

Catch exit passageway conflicts before issue

Helonic compares every sheet that touches an exit passageway for doors and penetrations that do not belong.